OME 890 2″ Rear Lift Coils for 1996-2002 Toyota 4Runner
ARB/OME 890 2″ Rear Lift Coils for 1996, 1997, 1998, 1999, 2000, 2001, 2002 Toyota 4Runner
Designed for superior performance across all terrain, an Old Man Emu suspension upgrade by ARB will provide noticeable improvements to a vehicle’s performance, including load carrying capacity and control characteristics.
Includes: 2x 2″ Lift OME 2890 Rear Coils for 96-02 4-Runner
for 500lbs of additional constant load
Questions and answers of the customers
I just installed 890x (2890) rear coils along with 5100 shocks. I'm getting 4.5" lift in the rear, which is 2" higher than the front with a 2.5" billstein lift. It looks ridiculous...not sure what to do? Can I cut the springs? This is for my 2wd 99 bare bones 4runner. I purchased these through your Amazon store. I can supply pictures if you like. Thanks.
Q I just installed 890x (2890) rear coils along with 5100 shocks. I'm getting 4.5" lift in the rear...... Read more answer nowA maybe need additional weight or retorquing sway bar or may sag after some time can't tell for sure if not ordered from us also front coils can be worn out and the front lift may not be the same as from the factory
i put a 3" lift kit on my 2000 4 runner SR5 2wd. the shop ordered new struts for front that had new springs with the 3" spacer.
the rear we added a 3" spacer as well but it is lower now than the front..... should i order springs with a 3" lift and remove the rear spacer or get stock springs and keep the spacer? looking for advice ASAP
- I plan to lift my 2001 toyota 4runner just an inch higher. Plan to by the 5100s. do i still need to by a coil for the rear? and if so, WHat do you recomment I buy?
- Is it possible to use this 2 in spring and add a 1nch spacer to achieve 3inches in total on the spring, to match your 2-3 nitro shock???
- I have a 99 4Runner. Wanting to do the 5100s with 2.5” lift in front with stock coils. What size rear coils do I need for the rear with stock weight?
Q I have a 99 4Runner. Wanting to do the 5100s with 2.5” lift in front with stock coils. What size ...... Read more answer nowA In order to figure out how much lift you need to level please take existing measurements from center of the wheel hub to the bottom of the fender. Difference between front and rear is how much lift you need to level. https://www.bilsteinlifts.com/level.png probably you need 2'' rear coils
Are the 890's side specific for the rear?
Q Are the 890's side specific for the rear?There are no answers for this question yet. Answer now
Hi, does this coils support heavy bumper?
Q Hi, does this coils support heavy bumper? answer nowA The OME 890 coils are intended for stock weight vehicles. I recommend OME 891 coils if you plan on running heavy bumpers.
Will they fit a 2wd 99?
Q Will they fit a 2wd 99? answer nowA yes, they will fit both 2DW and 4WD 4Runner 1999
do they come in pairs?
Q do they come in pairs? answer nowA Yes, priced per pair
I have the B8 5100 shocks installed on my 98 4runner, will these springs work with that set up or would I need to change to the long travel shocks to accommodate?
- Do I need to replace my rear shocks if I want to add these rear coils ?
Q Do I need to replace my rear shocks if I want to add these rear coils ? answer nowA Hello This 3 inch coils If you used to have a smaller coils, for example, a stock or there was a lift of 1-2 inches, then you will need to buy longer shocks.
Hi - Which Bilstein shock should I use with this? Also, whicc Bilstein shock should I use for front with factory springs?
Q Hi - Which Bilstein shock should I use with this? Also, whicc Bilstein shock should I use for fro...... Read more answer nowA You'll need this * * * https://bilsteinlifts.com/shop/toyota-4runner/1996-2002/shocks-96-02-toyota-4runner/long-travel-bilstein-5100-rear-shocks-1996-2002-toyota-4runner/ * * * or this * * * https://bilsteinlifts.com/shop/toyota-4runner/1996-2002/shocks-96-02-toyota-4runner/toytec-boss-rear-3-lift-shocks-1996-2002-4runner/