ToyTec 2.5″-3″ Lift Front Coil Springs

Rated 5.00 out of 5 based on 4 customer ratings
(4 customer reviews)

Base Price: $199.99

Found a better price?

Description

ToyTec 2.5-3″ Lift Front Coil Springs

Part Number 521600

  • Designed to increase ground clearance, for better off-road clearance and performance. The added suspension travel delivers a more responsive, more controlled ride over rough terrain, and gives you the additional wheel-well clearance to use bigger, higher-performance off-road wheels and tires.

Kit includes:

  • Toytec 2.5″ lift springs
    • 2.5″ average lift heights are with stock front weight on ’05-15 Tacoma, ’10+ 4Runner and 07+ FJ Cruiser.
  • Add top plate spacers from dropdown for 3″.
  • If used with Bilstein 5100 shock, bottom clip setting is recommended.
  • 600LB coils will help support extra weight.
  • Sold as a pair, (2) front coils

4 reviews for ToyTec 2.5″-3″ Lift Front Coil Springs

  1. Rated 5 out of 5

    brad hardee

    thank u nice fiting coil springs

  2. Rated 5 out of 5

    Sean Buckley (verified owner)

    Great set of springs. Gave me 3 inches of lift without sacrificing travel on my struts. Used the stock setting ring on the Bilstein 5100 adjustables. Only improvement would be that they did not come with installation instructions to add spacer…but common sense took over and I figured it out. Just would’ve been nice to have something to reference. Good purchase. I will buy again!

  3. Rated 5 out of 5

    Rob (verified owner)

    installed with existing Billstein 5100’s on lowest setting with top plate spacers and 1/4 inch drivers side, on 2006 Tacoma single cab. sits great, rides decent, good quality products.

  4. Rated 5 out of 5

    Ryan (verified owner)

    Fast shipping and great products very satisfied

Add a review

Questions and answers of the customers

  1. Answered by the admin For TRD PRo we can offer https://www.bilsteinlifts.com/shop/toyota-tacoma/2005-2015/front-lifts-and-coilovers/1-front-lift-baja-trd-toyota-tacoma/ These coils need longer shocks to be used
  2. Answered by the admin Hello 2.5" average lift heights are with stock front weight on '05-15 Tacoma, '10+ 4Runner and 07+ FJ Cruiser. Add top plate spacers from dropdown for 3". If used with Bilstein 5100 shock, bottom clip setting is recommended. 600LB coils will help support extra weight.
  3. Answered by the admin It is not recommended to stack lifts, we can't guarantee it will work good for more lift expensive lift kits with subframe are needed. You may consider adding body lift
  4. Answered by the admin Right, with these coils lowest notch adjustment is to be set
  5. Answered by the admin UCA's are recommended but not require, the benefit of the UCA's is to  fix the caster when the vehicle is getting aligned and also helps you a  lot with articulation on the front end. Setting 5100s to the lowest clip will give you about 1.5'' of lift, second clip will give you about 3''
  6. Answered by the admin For 2014 Tacoma single cab 4cyl engine they will give you from 2.5 to 3'' of front lift depending on additional weight carried on the bottom clip setting. I'd try it without spacers first, because it's too ligth single cab and it is possible it'll give you more then 3'' using spacers, which is not recommended.
  7. Answered by the admin Can't tell for sure - we haven't tested it by ourselves
  8. Answered by the admin If used with Bilstein 5100 shock, bottom clip setting is recommended. Will be 2.5-3'' lift. Exceeding 3'' of front lift can damage the suspension.
  9. Answered by the admin If used with Bilstein 5100 shock, bottom clip setting is recommended not to exceed 3'' of total lift. Exceeding can damage the suspension, steering, break lines and cv axles.
  10. Answered by the admin Will fit, but please note that more then 3'' of lift is not recommended in order not to damage the suspension and cv axles (if 4WD), so the lovest notch adjustments on 5100 shocks are to be used. Also diff drop kit is recommended for 4WD models.
  11. Answered by the admin These coils must be used with shocks which have 3'' greater extended length then the stock shocks.
  12. Answered by the admin will work if the 6112s extended length is 3'' greater then the stock shocks extended length
  13. There are no answers for this question yet. Answer now

Send me a notification for each new answer.
ATTENTION STATE OF CALIFORNIA CONSUMERS. WARNING: Cancer and reproductive harm – www.p65warnings.ca.gov