Pro Comp 1″ Rear Lift Block and U-Bolt Kit for 1995-2020 Toyota Tacoma
Pro Comp 1″ Rear Lift Block & U-Bolt Kit for 1995, 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003, 2004, 2005, 2006, 2007, 2008, 2009, 2010, 2011, 2012, 2013, 2014, 2015, 2016, 2017, 2018, 2019, 2020 Toyota Tacoma
Part Number: EXP65151 / 65151
- Block With U-Bolt Kit
- 1 in. Lift
- Incl. Block
Pro Comp Lift blocks. Kit includes 2 Cast Iron Riser Blocks, 4 U-Bolts, 8 Heavy Duty flat washers, and 8 Hi-nuts.
Questions and answers of the customers
Fits to 2020 Tacoma?
Q Fits to 2020 Tacoma? answer nowA it will fit for 2020 Toyota TacomaFour Wheel Drive •Position On Vehicle:Rear
Hi there. How long is the U bolt? I'm planning to use this kit and the add a leaf kit to lift my 2003 Tundra 2.5 inch high and not sure if it will work. Thanks.
- Please define the grade and length of ubolts
Q Please define the grade and length of ubolts answer nowA Please specify what u-bolts you need in the order notes
I recently ordered the 5100 3'' adjustable lift suspension kit w/2'' add-a-leafs for my 2010 toyo tacoma access cab. the place that i had install it informed me about toyotas leaf recall and advised me to call see if adding the leafs would void the warranty? this ended up being the case and the leafs were left off. now that the new leafs are on Im ready for the add-ons. currently the front end is noticeably higher than the rear. i know that the new leafs should add some hight but am wondering if the blocks will be necessary as well? the distance between the fender and the wheel is currently 1.5' higher in the front.
- I actually have a 07 Tacoma reg cab 4cyl Prerunner . Dealer just did a recall on the rear leafs which added a new leaf set "4" in total the old set had 3. Now the trucks rear end is higher by 3/4 to an 1". Was waiting for that to happen before I ordered the 5100's. From what I have read the 5100's set at 1.75 should level the truck, does this seem right to you? Thanks for your expertise and help, much appreciated.
Q I actually have a 07 Tacoma reg cab 4cyl Prerunner . Dealer just did a recall on the rear leafs w...... Read more answer nowA We do not know how much lift you need to level your exitsting setup. 1.75" Sounds about right, but what we always recommend is taking current measurements of the front fender to wheel and rear to see how much lift you need to level. May try useng the 3rd clip for 1.75'' (if you have stock front coil springs and if you ordered the Bilsteins with the regulated height clip).
Have a 2007 Toyota Tacoma Prerunner and am looking to get Bilstein 5100 F+B. Looking to set the front shocks at 1.75, would this block be needed to make the truck sit level? Thanks
Q Have a 2007 Toyota Tacoma Prerunner and am looking to get Bilstein 5100 F+B. Looking to set the f...... Read more answer nowA
Will not be needed if you have the Crew Cab V6 engine model (they have more weight on the front axle then the regular cabs 4cyl models and so the front sits slightly lower),
Also the front and rear lift difference will depend on if you often carry lot of weight and on your rear suspension condition.
We recommend to install the front lift first, and take measurements after that.
You may need only couple or only one of: https://bilsteinlifts.com/shop/toyota-tacoma/1995-2004/rear-lifts-95-04/12-solid-steel-axle-shim-for-toyota-tacoma/ plates. If your rear will be too low - then you may use blocks https://bilsteinlifts.com/shop/toyota-tacoma/1995-2004/1-inch-rear-blocks-without-u-bolts/ or add a leafs https://bilsteinlifts.com/shop/toyota-4runner/1986-1989/rear-procomp-aals-firm-ride/ - depending on if you ride empty or often carry much heavy stuff.